Baler Avermann, type AVOS 2010 BRK5-150/170, press power 170 tons, yoc 2016, only 9.500 operating hours, drive power 2 x 75 kW, fully equipped

Technical data baler

Manufacturer Avermann

Type AVOS 2010 BRK5-150/170

Year of construction 2016

Hours of operation approx. 9,500 hours

Press power 170 tons

Specific press capacity 140,5 N/cm²

Feed channel 2,000 x 1,000 mm

Theoretic cycle time 21 sec.

Theoretic  throughput capacity 680 m³/hour

Bale size 1,100 x 1,100 mm, lenght variable

Drive power 2 x 75 kW (Press operation also possible with only one pump)

Connected load with only one pump in operation 105 kW

Connected load with both pumps in operation 180 kW

Maximum connected load, total 200 kW

Fuse protection max. 315 A

Multi Cross Tying System 5-fold, vertical, 4-folg horizontal, fully automatic, the multi tying system can be converted to 4 mm PET plastic wire

Throughput capacity at a

bulk weight of 30 kg/cbm approx. 19 tons/hour

bulk weight of 50 kg/cbm approx. 32 tons/hour

bulk weight of 100 kg/cbm approx. 40 tons/hour

Bale weight up to 1,200 kg, depends on length and material

SPS controller Siemens S7 300

Operating panel Schneider Magelis Touch Panel

Baler dimensions built up 15,782 x 4,858 x 4,550 mm (l x w x h)

Transport weight baler, empty, approx. 46 tons total / 36 tons only the main press, without the dismantled press channel and tying systems.

Equipment and special features on the press

a.    WPL (Wear Plate Lined)
The entire baling chamber is completely lined with screwed, wear-resistant Hardox steel plates on the floor and side walls.

b.    OptiCut (optimised cutting system)
The optimised cutting system with energy-saving cutting geometry and material return bed, cuts even undissolved bale goods.

c.     MTS (Multi Tying System)
9-fold cross tying system (5-fold vertical, 4-fold horizontal, individually switchable depending on the material recipe). The multi tying system can also be converted from soft-annealed steel wire to a 4 mm PET plastic wire for combustion (external special accessory).

d.    MaxDrop (Maximum Drop Chute)
The volume-maximised drop chute with 2,000 x 1,000 mm ensures optimised material distribution in the press chamber and maximum throughput rates for lightweight materials such as film, DSD material, lightweight plastic fractions, RDF fractions, etc.

e.    ReSys (Restaint System)
6-fold articulated restraint system for highly expanding material such as films, PET bottles, hollow plastic bodies such as bottles, buckets, canisters and drums.

f.      TSM (Two Stage Mode)
Press can be operated with one or two pumps (energy-saving use with only one 75 kW motor, e.g. in late shift or night shift operation).

g.    RMS (Remote Maintenance System)
Industrial router with remote maintenance system

h.    ICS (Indoor Cooling System)
Indoor Air-conditioning system in the control cabinet without air exchange, so that no dust and dirt is sucked into the control cabinet.

Condition of the baler

With only approx. 9,500 operating hours in 4 years after initial installation, this is a young machine in an extremely good condition. All steel wear parts in the press chamber and press channel as well as on the tying systems show hardly any signs of wear. The press is immediately ready for use again after cleaning and carrying out the normal maintenance intervals, such as greasing.

The equipment of this icon of German engineering leaves hardly anything to be desired. The technical construction and design are "state of the art" and need not fear any comparison with market competitors.

Scope of delivery for the baler

Baler AVOS 2010 BRK5-150/170

Feed hopper on the feed chute

Two maintenance platforms with access ladder

18 wire coil stands with gallows and wire deflection (without wire)

Bale slide

Machine documentation in German:

Operating manual

CE declaration for the baler

Electrical wiring diagram

Hydraulic circuit diagram

Installation plan

Foundation plan

Transport logistics

Three trucks are needed for the removal, one low loader with special permit for the main frame of the machine, weight approx. 36 tons.

Two more normal tautliners are needed for the various attachments, weight per truck < 20 tons.

Comments:

The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available.  Inspections are possible after agreement.  We will not assume liability for the given technical data and possible errors.