Baler BOA Impress D130-110-A-5-1.6-RE.W, press power 127 tons, yoc 2008, drive power 2 x 55 kW, special construction for extreme wet residual waste

Technical data baler

Manufacturer BOA

Type Impress D130-110-A-5-1.6-RE.W

Year of construction 2008

Hours of operation approx. 50,000 h, Stand November 2019

Press power main press 1,266 kN / 127 tons

Specific press capacity 16,4 kg/ cm²

Feed channel 1,620 x 1,000 mm (l x w)

Capacity per cycle time 2,9 cbm

Cycle time under operating conditions 22 sec.

Throughput rate under operating conditions up to 525 cbm/h

Bale size 1,100 x 720 mm, length variable

Driving motor 2 x 55 kW

Connected load 155 kW

Tying system 5-fold vertical, fully automatic

Throughput rate at a

bulk weight of 30 kg/cbm approx. 12 tons/h

bulk weight of 50 kg/cbm  approx. 20 tons/h

bulk weight of 100 kg/cbm approx. 28 tons/h

bulk weight of 150 kg/cbm  approx. 35 tons/h

bulk weight of 200 kg/cbm approx. 44 tons/h

Bale weight up to 800 kg, depends on material

Volume hydraulic oil tank 1,850 l

Hydromat type H200-5 horizontal

SPS controller (manuf., type) Siemens S7

Operating panel (manuf., type)  Siemens Simatic Touchscreen

Baler dimensions built up with hopper 11.310 x 2.759 x 6.913 mm (l x w x h)

Dimensions press channel 3,500 x 1,100 x 720 mm (l x w x h)

Machine weight baler approx. 44 tons

 

Special equipment on the press:

-       Hydraulic wire tensioning device at the end of the press

-       Special press ram with hydraulically opening needle channels during the setting process

-       Complete lining of the pressing chamber with wear-resistant HARDOX steel plates on the floor and side walls

-       Mechanically pivoting Hydromat for easier maintenance and cleaning

-       Covering of the lateral press channel with hinged splash guard plates made of stainless steel, for the pressing of extremely wet residual waste

 

Current operation:

The press is currently used by a municipality, mainly for pressing dry and extremely wet residual waste from municipal collection. The machine is also used to compress paper, cardboard and board from press containers. 

 

Scope of delivery:

Only the press incl. documentation, control cabinet and bale slide.

 

 

NOT included in the scope of delivery are the conveyor belt with feed chute and conical intermediate chute, the wire drawing stations and the mechanical clearing system for sludge and pasty residues located under the press.

 

Dismantling and loading:

The press is expected to be dismantled by a specialist company at the end of the second quarter and will also be loaded immediately onto a low-loader, as there is no space available on site for storing the machine. The buyer must comply with the dismantling company when transporting the press away and provide a low-bed trailer punctually for the loading date on the construction site.

 

Comments:

The press is in good condition, has been regularly serviced and is currently in use. The documentation (Manual, CE, electr./hydr.-drawings), are completely available.  Inspections are possible after agreement.  We will not assume liability for the given technical data and possible errors.

 

Please note:

  • All technical data refer to specifications of producer/owner. We will not assume liability for the given statements and possible errors.
  • This offer is non-binding, prior sale excepted und revocable at any time.
  • Inspections possible after agreement. 
  • The sale is ex location, as it stands and lays, without liability and guarantee.